1. Introduction

Last updated and tested: 2024-10-23

We have prepared for you a ready-made OpenATV 7.4 firmware with Oscam iCam v9 installed and configured for Dreambox One (AArch64 cpu)

Attention! After installing the firmware, all data on your receiver will be deleted! Including your scanned channels, etc. Therefore, before installing, we strongly recommend that you make a full backup of your receiver!

After installing the firmware, you will need to make some settings – if necessary, change the configuration of your tuner, as well as specify your data for connecting to the CS server.

If you don’t have a Dreambox One receiver, please use other article!

2. Firmware installation on Dreambox One

1. Download the image from HERE
2. Extract the USB image (it is a .zip archive) on your PC using your favorite unzip tool. The result is that you get a  dreamone directory and in this directory you find a rootfs.tar.bz2 file.
3. Power off Dreambox ONE UHD via the rocker switch on the rear panel.
4. Turn on the Dreambox ONE UHD from the switch on the back, as soon as the LED above the on / off button lights up hold down with a finger upwards and release immediately after that the IP address will appear on the TV screen. Or reboot the receiver in Recovery mode via the menu!
5. Type the ip address of the Dreambox ONE UHD into a browser then press enter.
6. Click the “Firmware” upload button.
7. Click “Browse” button. Search for the downloaded image (rootfs.tar.bz2 file), double click on it then Press the Go! button. And wait!
   Important: Remove check marks from Backup and Restore Settings
8. When you see the message: [*] Finished successfully. You may reboot now.
   Click the “Click here to reboot” button.

3. Setting up the receiver after flashing

3.1 Tuner Configuration

If, after flashing and turning on the receiver, the “kabel eins” channel did not work for you, then you need to change the tuner settings. To do this, go to the MENU -> Setup -> Reception -> Tuner Configuration section and configure your tuner.

3.2 Obtaining the IP address of the receiver

By default, the receiver should obtain a network address automatically (DHCP). To find out, you need to go to the section MENU -> Information -> Network

Connection status must be Up / Active, IP address must be defined (In my case it is 192.168.1.219)

If for some reason your receiver did not receive an address automatically, then you need to set up the network manually. This can be done in the section MENU -> Setup -> System -> Network -> Device Settings -> Adapter Settings

3.3 Setting up the Oscam

You need to add your access parameters to Oscam. To do this, open the Oscam Web Interface in a browser using the IP of your receiver. Oscam Web Interface is located on port 8080. In my case it is:

http://192.168.1.219:8080/

You need to go to the Files -> oscam.server section, specify your connection data taken from the billing and click the Save button.

Don’t forget to click the Save button!

4. Reboot the receiver

Please reboot the receiver completely after setup. Do not turn off the receiver from the socket, but reboot it through the menu MENU -> Standby / Restart -> Reboot

After rebooting the receiver, you can go to the Sky Deutschland iCAM bouquet and enjoy watching.

5. Choose a playlist and watch!

After rebooting the receiver, you can go to the Sky Deutschland iCAM bouquet and enjoy watching.

6. Additional Information

Installed firmware has a root password for remote access via SSH / Telnet:

Login: root 
Password: icam2022

We recommend that you change the root password, and restrict or disable remote access if you do not need it.

7. Changing ROOT password

To increase the security of your receiver, we strongly recommend that you change the root password.
In order to change the root password, log in to the receiver using SSH or Telnet using the login and password specified in paragraph 6. Enter the command:

passwd root

and set your new password